background image

27

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Installation Instructions

901140-00, 01/2021

Innovative Hearth Products
DRT63ST-B Power-Vent Direct-Vent Fireplaces

Separate glowing ember material  

into 

THIN

, square, dime-sized pieces.

Figure 39 - Preparation of Glowing Ember Material

Bag of Glowing Embers

       WARNING

 

DO NOT attempt to install the logs until the appli-

ance installation has been completed, the gas line 

connected and tested for leaks, and the initial burner 

operation has been checked out. 

 

Logs get very hot and will remain hot up to one hour 

after gas supply is turned off.  Handle only when 

logs are cool. Turn off all electricity to the appliance 

before you install

 

volcanic stone, embers and logs.

 

The size and position of the log set was engineered 

to give the appliance a safe, reliable and attractive 

flame pattern.  Any attempt to use a different log 

set in the fireplace will void the warranty and will 

result in incomplete combustion, sooting, and poor 

flame quality.

 

This appliance is not designed to burn wood.  Any 

attempt to do so could cause irreparable damage to 

the appliance and prove hazardous to your safety.

 

If logs are not installed according to the log installa-

tion instructions, flame impingement and improper 

combustion could occur and result in soot and/or 

excessive production of carbon monoxide (CO), a 

colorless, odorless, toxic gas.

Step 9. INSTALL VOLCANIC STONE, GLOWING EMBERS,  

AND LOGS

9-1.

  Remove barrier, modesty panel, and glass door assembly from one 

side of fireplace. See 

Page 30

.

9-2. 

Locate materials (log set, bag of glowing embers, and bags of 

volcanic stone). 

NOTE: LOGS ARE FRAGILE! 

Handle with care to prevent 

breakage.

9-3.

 Install volcanic stone. Place some of the volcanic stone on the 

firebox floor around the grate (the entire bag of volcanic stone will 

NOT be used). 

NOTE: 

Do NOT place volcanic stone on burner.

9-4. 

Prepare and install glowing embers. 

NOTE: 

This appliance is provided with enough glowing 

ember material for several applications. Do NOT use 

the entire contents of a new bag at one time.

a)  Separate some of the glowing ember material into pieces 

about 

the size and thickness of a dime 

(see 

Figure 39

).

 Keep the 

pieces fluffed up, not matted. 

  IMPORTANT! Ember pieces must be  

        as SMALL and THIN as a dime. 

b)  Distribute the dime-sized pieces over all burner ports.

NOTE: 

To prevent flame impingement and soot, do not use 

more ember material than necessary.

c)  For best glowing effect, replace ember material annually.

 

NOTE: 

Use only catalog number H8312 Platinum Glowing 

Embers with this fireplace.

NOTE: It is important to ensure proper log placement 

per the manual when installing these units. Verify pilot 

flame is not obstructed. See Verifying Appliance Opera-

tion on Page 26.

1. 

Install logs (reference 

Figure 40)

NOTE: Logs are FRAGILE! Handle with care to prevent breakage

.

K

G

I

J

F

D

E

B

H

C

A

Figure 40 - Top View of Logs

2.  Begin log installation from the control side of the unit. Pilot and 

orifice should be on the right side of the burner assembly (

see

 

Figure 41

).

Pilot

Figure 41

View from Control Side

Содержание DRT63ST



























































Отзывы: