SuperFlow SF-1020I Скачать руководство пользователя страница 14

Страница: 14 / 80

4.0 Installation

4.1 Installation

4.1.1 Room Requirements

The SF-1020i flowbench should be placed in a relatively open area, free from loose debris such as metal

filings or chips from machining tools. The flowbench, in essence, is a giant vacuum cleaner that will ingest

rags, papers, and anything nearby that is not secured.

Space the flowbench with a minimum of 6 inches (15.2 cm) on all sides from any equipment or walls.

A power distribution box with a disconnect switch and plug receptacle (supplied by others) should be

located near the flowbench. Superflow recommends using twist-lock connectors. The power requirements

for the SF-1020i can be either 480 VAC, 40A, three-phase, 50 or 60 hz or 380 VAC, 40A, three-phase,

50 or 60 hz. The power source must be protected with the appropriate sized fuse or circuit breaker. The

SF-1020i has internal circuit breakers for the electronics but no internal over-current protection for the

motor.

If the flowbench is in a small room and the exhaust of the bench is also vented into the same room, after a

while, the flowbench may heat the area. Conditioning the air for temperature or humidity is not necessary

but would be more comfortable for the operators.

4.1.2 Unpacking

The SuperFlow SF-1020i flowbench is shipped in a carton.

•

Carefully remove the flowbench from its shipping carton

• Place it on a level surface

2. Other boxes or cartons may also be shipped that contain accessories and options provided with the

flowbench.

4.1.3 Electrical

1. Wire an appropriate sized power cord (supplied

by others) to main incoming power connections

located behind right side panel.

2. Utilize a twist-lock plug connector (supplied by

others) on opposite end of the power cord to

connect SF-1020i flowbench to properly sized

power source. Ensure the main power circuit

OFF

before connecting the flowbench power

cord to the power source.
• Refer to "4.1.1 Room Requirements" above

and supplied wiring schematic.

Before installation, be sure the main

voltage and current type specified

in the identification plate match the

supply voltage and current type

at the place of use, and ensure the

circuit being used is adequately

protected.

WARNING

Refer to your local electrical code for the proper

power cord size and connector type.

NOTICE

Содержание SF-1020I

















































































Результаты поиска

Содержание SF-1020I

Отзывы:

Похожие инструкции для SF-1020I

Бренды по названию

Популярные бренды

SuperFlow SF-1020I, Руководство оператора

Результаты поиска

Содержание SF-1020I

Отзывы:

Похожие инструкции для SF-1020I

Бренды по названию

Популярные бренды