manualshive.com logo in svg

Stryker SmartPump Rx, Инструкция по эксплуатации

Поделиться
Скачать
Stryker SmartPump Rx Скачать руководство пользователя страница 49

 

 

Specifications 49 

Electromagnetic Compatibility Information 

This equipment has been tested and found to comply with the limits for medical devices to IEC 60601-1-
2:2001. These limits are designed to provide reasonable protection against harmful interference in a typical 
medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to other devices in 
the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to other devices, which can be determined by turning the 
equipment off (with AC power cord unplugged) and then on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 
 

•

 

reorient or relocate the receiving device 

•

 

increase the separation between the equipment 

•

 

connect the equipment into an outlet on a circuit breaker different from that to which the other 
device(s) are connected 

•

 

consult the manufacturer or field service technician for help. 

 
Only Stryker printer and shielded serial cable may be connected to the equipment’s serial port. Usage of 
accessories or cables other than those sold by Stryker may result in increased RF emissions or decreased 
RF immunity of the equipment. 

 

 

 

 

Guidance and manufacturer’s declaration – electromagnetic emissions 

The Dual Channel SmartPump is intended for use in the electromagnetic environment specified below. The customer 

or the user of the Dual Channel SmartPump should assure that it is used in such an environment. 

Emissions test 

Compliance 

Electromagnetic environment - guidance 

RF emissions 

CISPR 11 

Group 1 

The Dual Channel SmartPump uses RF energy only for its internal function. 

Therefore, its RF emissions are very low and are not likely to cause any 

interference in nearby electronic equipment. 

RF emissions 

CISPR 11 

Class A 

Harmonic emissions 

IEC 61000-3-2 

Class A 

Voltage 

fluctuations/flicker 

emissions IEC 

61000-3-3 

Complies 

The Dual Channel SmartPump is suitable for use in all establishments other 

than domestic establishments and those directly connected to the public 

low-voltage power supply network that supplies buildings used for domestic 

purposes. 

 

Содержание SmartPump Rx

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды