Stryker 6086 Скачать руководство пользователя страница 9

Страница: 9 / 158

www.stryker.com

6086-009-001 REV B

Return To Table of Contents

SPECIFICATIONS

Safe Working Load

Note:

Safe Working Load indicates the sum of

the patient mattress and accessory weight.

700 pounds

317,5 kg

Backrest Articulation/Shock Position

0° to 73° / +15°

Overall Length/Minimum Length/Width

80" / 64" / 23"

203,2 cm / 162,6 cm / 58,4 cm

Height

Position 1

13.8”

35,1 cm

Position 2

22”

55,9 cm

Position 3

25.8”

65,5 cm

Position 4

28.1”

71,4 cm

Position 5

31.9”

81 cm

Position 6

34.6”

87,9 cm

Position 7 (LOW)

37.3”

94,7 cm

Position 8 (MID)

40”

101,6 cm

Position 9 (HIGH)

42.2”

107,2 cm

Weight

89 lb

40,37 kg

Caster Diameter/Width

6" / 2"

15,2 cm / 5,1 cm

Minimum Operators Required for an Occupied Cot

Minimum Operators Required for an Unoccupied Cot

Recommended Fastener Systems

Model 6370 or 6377 Floor Mount Type
Model 6371 Wall Mount Type

Maximum Loading Height

Up to 34"

Up to 86,4 cm

Single Wheel Lock / Double Wheel Lock

Optional

Height is measured from the bottom of the mattress at seat section to ground level.

Cot is weighed without mattress and restraints.

Load wheel height can be set between 27.25” (69,2 cm) and 34” (86,4).

Stryker reserves the right to change specifications without notice.
The

Performance-PRO™ XT

is designed to conform to the Federal Specification for the Star-of-Life Ambulance (KKK-A-1822).

The

Performance-PRO™ XT

is designed to be compatible with competitive cot fastener systems.

Patents pending.

The yellow and black color scheme is a proprietary trademark of Stryker Corporation.

Introduction

Содержание 6086































































































































































Результаты поиска

Содержание 6086

Отзывы:

Бренды по названию

Популярные бренды

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 6086

Отзывы:

Бренды по названию

Популярные бренды