manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 36

36

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Operation Guide

Figure 30:  Head Section Extended

Figure 31:  Head Section Retracted

Figure 32:  Head Section Release Handles

A

OPERATING THE RETRACTABLE HEAD SECTION

The head section telescopes from a first position suitable for 
loading the cot into an emergency vehicle to a second position 
retracted within the litter frame. When retracted, the cot can 
roll in any direction on the caster wheels even in the lowest 
position, allowing improved mobility and maneuverability.

To extend the head section:

1.  Grasp the outer rail with one hand for support and pull 

the handle (A),  rotating the handle towards the head end 
of the cot to release the head section from the locked 
position

2.  While holding the handle (A) in the released position, pull 

the head section away from the litter frame, lengthening 
the head section until it engages in the fully extended 
position.

3.  Release handle (A) to lock the head section in the extended 

position.

To retract the head section:

1.  Grasp the outer rail with one hand for support and release 

the handle (A),  rotate the handle towards the head end 
of the cot to release the head section from the locked 
position.

2.  While holding the handle (A) in the released position, push 

the head section toward the litter frame, retracting the 
head section until it engages in the retracted position.

3.  Release handle (A) to lock the head section in the retracted 

position.

 WARNING

• 

To avoid injury, always verify that the head section is 
locked into place prior to operating the cot.

• 

Do not attempt to load the cot into the patient compartment 
with the head section retracted. Loading the cot with the 
head section retracted may cause the product to tip or not 
engage properly in the cot fastener, possibly causing injury 
to the patient or operator and/or damage to the product.

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды