Stryker 6086 Скачать руководство пользователя страница 50

Страница: 50 / 158

6086-009-001 REV B

www.stryker.com

Optional Accessories

ATTACHING AN OXYGEN BOTTLE TO AN OXYGEN BOTTLE HOLDER

To attach an oxygen bottle:

1. Place an oxygen bottle in the holder.
2. Insert the lower strap through the buckle and affix the strap onto itself to secure the oxygen bottle to the holder.

Note:

Inspect the straps and clips for wear between use and replace the strap if it is no longer holding the oxygen

bottle.

CAUTION

•

To avoid damage to the oxygen bottle holder (if equipped), the weight of the equipment must not exceed 40 lb (18
kg).

•

Do not use two head end oxygen bottle holders at the same time.

Note:

The optional fowler oxygen bottle holder (p/n 6500-141-000) is not compatible with the optional retractable head

section oxygen bottle holder (p/n 6085-046-000).

Содержание 6086































































































































































Результаты поиска

Содержание 6086

Отзывы:

Бренды по названию

Популярные бренды

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 6086

Отзывы:

Бренды по названию

Популярные бренды