manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 33

www.stryker.com

6086-009-001 REV B

33

Return To Table of Contents

Operation Guide

UNLOADING AN EMPTY COT FROM A VEHICLE WITH ONE OPERATOR

 WARNING

• 

The one person loading and unloading procedures 
are for use only with an empty cot. Do not use the 
procedures when loading or unloading a patient. Injury 
to the patient or operator could result. 

• 

Do not pull or lift on the safety bar when unloading the 
cot.  Damage to the safety bar could result and injury 
to the patient or operator could occur. 

• 

Ensure proper hand placement on hand grips. Hands 
should be clear of red safety bar pivots while loading 
and unloading the cot or whenever changing height 
position of the cot with two or more operators.

To unload an empty cot from a vehicle with one 
operator:

 

1.  Lift the vehicle bumper to the raised position (if 

equipped). 

2.  Disengage the cot from the cot fastener.  (For more 

information about the cot fastener, see 

page 17

). 

Grasp the cot frame at the foot end; pull the cot from 
the vehicle until the safety bar engages the safety hook 
(see Figure 26). 

3.  Lower the foot end of the cot to the ground (see Figure 

27). 

4.  Squeeze and hold the release handle (see Figure 28) 

and raise the foot end of the cot back to a level position 
with the compartment floor. 

5.  Disengage the safety bar from the safety hook by 

pushing the safety bar release lever forward and roll 
the cot out of the vehicle. 

Figure 28:  Squeeze the Release Handle

Figure 26:  Pull the Base of the Cot

Figure 27:  Lower the Foot End of the Cot

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды