Stryker 6086 Скачать руководство пользователя страница 46

Страница: 46 / 158

6086-009-001 REV B

www.stryker.com

Optional Accessories

USING THE EQUIPMENT HOOK

Use the equipment hook (A) (see Figure 46) to hang additional accessories or equipment, such as defibrillators or
monitors.

CAUTION

To avoid damage to the equipment
hook, the weight of the accessories
or equipment must not exceed 35 lb
(15.9 kg).

Figure 46: Equipment Hook

USING THE HEAD EXTENSION WITH PILLOW

You can install the head extension assembly over the fowler to provide head end support.

Attach the pillow to the head extension by placing the support into the flap on the bottom of the pillow. Secure the
pillow to the Velcro

on the bottom of the support.

Note:

The head extension with pillow (p/n 6100-044-000) is not compatible with the optional equipment hook (p/n

6500-147-000) or optional fowler oxygen bottle holder (p/n 6500-141-000).

Содержание 6086































































































































































Результаты поиска

Содержание 6086

Отзывы:

Бренды по названию

Популярные бренды

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 6086

Отзывы:

Бренды по названию

Популярные бренды