manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 26

26

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Operation Guide

TRANSFERRING THE PATIENT TO THE COT

To transfer the patient to the cot:

1.  Roll the cot to the patient.
2.  Place the cot beside the patient and raise or lower the cot to the level of the patient.
3.  Lower the siderails and open the restraint straps.
4.  Transfer the patient to the cot using accepted EMS procedures.
5.  Use all the restraint straps to secure the patient to the cot (see 

page 40

).

6.  Adjust the backrest and foot rest as necessary.

Note:  

When transferring larger patients, use of the Transfer Flat (6005-001-001) is recommended.

 WARNING

• 

Always use all restraint straps to secure the patient on the cot.  An unrestrained patient may fall from the cot and 
be injured.

• 

Never leave a patient unattended on the cot or injury could result.  Hold the cot securely while a patient is on the 
product.

• 

Never apply the optional wheel locks while a patient is on the cot.  Tipping could occur if the cot is moved while 
the wheel lock is applied, resulting in injury to the patient or operator and/or damage to the cot.

• 

Siderails are not intended to serve as a patient restraint device.  See 

page 40

 for proper restraint strap usage.   

Failure to use the restraint straps properly could result in patient injury.

ROLLING THE COT

When rolling the cot:

• 

Make sure that all of the restraint straps are securely buckled around the patient (see 

page 40

).

• 

Position an operator at the foot end and one at the head end of the cot 

at all times

 when rolling the cot with a 

patient on it.

• 

Approach door sills and/or other low obstacles squarely and lift each set of wheels over the obstacle separately.

 WARNING

• 

High obstacles such as curbing, steps or rough terrain can cause the cot to tip, possibly causing injury to the 
patient or operator.  

• 

If the cot is equipped with the optional kickstand, make sure that the kickstand remains in the retracted position 
and does not engage during transport.

• 

Transporting the cot in lower positions reduces the potential of a cot tip.  If possible, obtain additional assistance or 
take an alternate route.

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды