manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 35

www.stryker.com

6086-009-001 REV B

35

Return To Table of Contents

Operation Guide

OPERATING THE SIDERAILS

To raise the siderails

, as shown in Figure 29, lift up on the siderail until the latch clicks and the siderail locks into place. 

To lower the siderails

, squeeze handle (B) to release the siderail latch. Guide the siderail down toward the foot end 

until flat.  Ensure that the siderails are lowered when a patient is being transferred to or from the cot.

 WARNING

Siderails are not intended to serve as a patient restraint device.  See 

page 40

 proper restraint strap usage. Failure to 

use the siderails properly could result in patient injury.

OPERATING THE BACKREST

To raise the backrest

, as shown in Figure 29, squeeze handle (A) for pneumatic assist in lifting the backrest to the 

desired height. 

To lower the backrest

, squeeze handle (A) and push down on the backrest frame until the backrest has reached the 

desired height. 

Figure 29:  Backrest Elevated and Siderails Raised

Head End

A

B

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды