manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 51

www.stryker.com

6086-009-001 REV B

51

Return To Table of Contents

Optional Accessories

USING THE RETRACTABLE HEAD SECTION OXYGEN BOTTLE HOLDER

To attach an oxygen bottle to the retractable head section oxygen bottle holder:

1.  Center the oxygen bottle on the cradled surface of item (A) as shown in Figure 54.
2.  Tighten both straps (B) around the oxygen bottle.
3.  Secure the slack on the straps to the Velcro

®

 on the straps.  

Note:  

Inspect the straps and clips for wear between use and replace the strap if it is no longer holding the oxygen 

bottle.

 

 WARNING

If the cot is equipped with the optional retractable head section oxygen bottle holder, use caution while the oxygen bottle 
holder is installed to avoid pinching your fingers between the fowler bracket and the oxygen bottle.

 

 CAUTION

• 

To avoid damage to the oxygen bottle holder (if equipped), the weight of the equipment must not exceed 40 lb (18 
kg).

• 

Do not use two head end oxygen bottle holders at the same time.

Figure 54:  Retractable Head Section Oxygen Bottle Holder

A

B

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды