Stryker 6086 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 158

Stryker 6086 Скачать руководство пользователя страница 17

www.stryker.com

6086-009-001 REV B

17

Return To Table of Contents

Note:

The Cot Fastener Installation instructions on

through

are intended for cots that you will

NOT use with Power-LOAD. For Model 6086 cots with the Power-LOAD option, see the Power-LOAD Operations/
Maintenance Manual for installation instructions.

The Stryker Cot Fastener Systems are designed to be compatible only with cots which conform to the installation
specifications listed on

.

WARNING

It is the responsibility of the cot operator to ensure that the cot being used in the Stryker Cot Fastener Systems meets the
installation specifications listed on

. Injury may result if a non-compatible cot is used in the Stryker Fastener

System.

Note:

Adjustment of the rail clamp assembly may be required in order to compensate for any variation in the cot

retaining post position depending on the cot manufacturer and model number.

For more information about the Stryker Cot Fastener Systems, see the Cot Fastener Operations/Maintenance Manual.

Cot Fastener Installation

«
...
15
16
17
18
19
...
»

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды