Still FXV 14 N Скачать руководство пользователя страница 66

Страница: 66 / 152

Joystick function (option)

The truck may be equipped with a joystick in

place of the control unit.
The operation is therefore different.

NOTE

Always operate the joystick slowly, as the

truck reacts immediately. Abrupt starts, brak-

ing or reversal of drive direction must be avoi-

ded at all costs.

Front of the joystick

The front of the joystick is used to:

●

Move the truck forwards or backwards

●

Raise or lower the forks

Forward travel

–

Push the joystick to the left (1) to travel for-

wards (opposite fork direction).

Reverse travel

–

Push the joystick to the right (2) to travel

backwards (fork direction).

Fork lifting

–

Tilt the joystick downwards (4)

Fork lowering

–

Tilt the joystick to upwards (3)



Use

Driving

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Похожие инструкции для FXV 14 N

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Похожие инструкции для FXV 14 N

Бренды по названию

Популярные бренды