Still FXV 14 N Скачать руководство пользователя страница 63

Страница: 63 / 152

Forward travel

–

Using your thumb, push the drive switch to

the left (2) to travel forwards (opposite fork

direction).

–

When the drive switch is released, the truck

brakes electrically.

Reverse travel

–

Using your thumb, push the drive switch to

the right (1) to travel backwards (fork direc-

tion).

–

When the drive switch is released, the truck

brakes electrically.

WARNING

Restricted visibility
During reverse travel, visibility may be restricted. Be

very careful. Make sure that the path behind is clear

before travelling backwards.

Reversing the drive direction

–

Push the drive switch in direction (1) or (2).

–

Release the drive switch.

–

Operate it progressively in the opposite di-

rection until the required speed is reached.

Braking

WARNING

The quality of the floor surface affects the braking

distance of the truck.
This should be taken into consideration when driving.



Use

Driving

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Похожие инструкции для FXV 14 N

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Похожие инструкции для FXV 14 N

Бренды по названию

Популярные бренды