Still FXV 14 N Скачать руководство пользователя страница 131

Страница: 131 / 152

WARNING

The electrolyte (diluted sulphuric acid) is poisonous

and corrosive.

–

Always wear suitable protective equipment (indus-

trial protection goggles, safety gloves) when work-

ing on a battery.

–

Never wear a watch or jewellery when handling

battery acid.

–

Do not allow any acid to get onto the clothing or

skin or into the eyes. If this does happen, rinse im-

mediately with plenty of clean water.

–

Immediately rinse away any spilled battery acid

with plenty of water.

–

In case of injury, seek medical advice immediate-

ly.

–

Always follow the safety information provided by

the battery manufacturer.

–

Comply with the regulations in force.

–

Check the battery acid level and electrolyte

density according to the battery manufactur-

er's recommendations.

–

The cell covers of the battery must be kept

dry and clean.

–

Any spillage of battery acid must be neutral-

ised immediately.

ENVIRONMENT NOTE

Dispose of any used battery acid in accord-

ance with the regulations.

Maintenance

Electrical equipment

121

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды