Still FXV 14 N Скачать руководство пользователя страница 54

Страница: 54 / 152

Seat heater option

The driver's seat may be equipped with the

seat heater option.
The heater turns on when the operator's pres-

ence on the seat is detected.
To activate the heater, proceed as follows:

–

Sit on the seat

–

Adjust the weight of the operator

–

Put the truck into service

–

Press the LED button (1) to activate the

heating

The LED button (1) illuminates to indicate that

the heater is in operation.

NOTE

When the driver gets up or leaves the seat,

the heating stops in order to conserve battery

power.

No visual information is shown on the display.

–

Check whether the LED button (1) is on

–

Press the LED button (1) to reactivate the

heater



Use

Driver's compartment settings

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды