Still FXV 14 N Скачать руководство пользователя страница 64

Страница: 64 / 152

Braking by reversing the drive direction

–

Move the drive direction switches (2) or (3)

in the opposite drive direction.

Braking by releasing the drive switch

–

While travelling, completely release the

drive switch.

The brake is automatically activated. The truck

is immobilised.

Electromagnetic braking

The electromagnetic brake is activated auto-

matically if one of the following conditions is

met:

●

The operator releases the operator pres-

ence pedal (decelerates and then brakes)

●

The operator gets up from the seat (decel-

erates and then brakes)

●

The drive switch is in the neutral position

●

The power supply is cut off

●

The operator presses the emergency off

switch

Horn

The horn is positioned on the rear side of the

control module.
It is used:

●

On routes where there is poor visibility

●

At junctions

●

In the event of immediate danger

–

Press the button (1) on the control module.

The horn sounds.



Use

Driving

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды