Still FXV 14 N Скачать руководство пользователя страница 62

Страница: 62 / 152

Driving

Defining directions

Names used in the text refer to the component

installation position with respect to the driver's

compartment.

●

Reverse travel (1)

●

Forward travel (3)

●

To the right (4)

●

To the left (2)

The load is positioned at the rear.

Driving

WARNING

Be aware of the position of the drive wheel
Slowly start the truck.
Check the position of the drive wheel on the display.

NOTE

Always operate the drive switch slowly, as the

truck reacts immediately. Abrupt starts, brak-

ing or reversal of drive direction must be avoi-

ded at all costs.

The drive switch is located on the control unit.

NOTE

Always keep hands and feet inside the driver's

compartment while the truck is moving.



Use

Driving

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды

Still FXV 14 N, Оригинальное руководство пользователя

Результаты поиска

Содержание FXV 14 N

Отзывы:

Бренды по названию

Популярные бренды