Still FXV 14 N Скачать руководство пользователя страница 102

Страница: 102 / 152

Charging the battery using an exter-

nal charger

CAUTION

Deep discharging may damage the battery.

–

Charge the battery immediately.

–

Park the truck safely.

–

Before charging, check the condition of the

battery cable and the charger cable. Re-

place them if necessary.

–

Open the hood and leave open.

–

Remove the battery handle connector (1)

from the truck plug (2).

–

Connect the battery connector to the wall-

mounted connector.

WARNING

Electrical risk
Only unplug the battery connector from the battery

charger when both the battery charger and truck are

switched off.

NOTE

Follow the instructions provided by the battery

and battery charger manufacturers (equalising

charge).

WARNING

Risk of damage, short circuit or explosion.
Do not place any metallic objects or tools on the bat-

tery.
Smoking is prohibited.

WARNING

The electrolyte (diluted sulphuric acid) is toxic and

very caustic.
Follow the safety regulations when handling battery

acid.



Use

Handling the battery

11748011551 EN - 02/2021 - 09

Содержание FXV 14 N

























































































































































Результаты поиска

Содержание FXV 14 N

Отзывы:

Still FXV 14 N, Оригинальное руководство пользователя, Страница: 102 / 152

Результаты поиска

Содержание FXV 14 N

Отзывы: