manualshive.com logo in svg

Stihl SP 81, Инструкция по эксплуатации

Поделиться
Скачать
Stihl SP 81 Скачать руководство пользователя страница 4

3

SP 81

English

Special safety 
precautions must be 
observed when working 
with this power tool 
because the rakes move 
at a high stroke rate.

It is important that you 
read and understand the 
instruction manual before 
using the unit for the first 
time. Keep the manual in 
a safe place for future 

reference. Non-observance of the safety 
precautions in the instruction manual 
may cause serious or even fatal injury.

Always observe local safety regulations, 
standards and ordinances.

If you have not used this type of power 
tool before: Have your dealer or other 
experienced user show you how to 
operate your power tool or attend a 
special course of training in power tool 
operation.

Minors should never be allowed to use a 
power tool. 
Bystanders, especially children, and 
animals should not be allowed in the 
area where a power tool is in use.

When the power tool is not in use (work 
break), shut it off so that it does not 
endanger others and secure it against 
unauthorized use.

The power tool user is responsible for 
avoiding injury to third parties or damage 
to their property.

Lend or rent your power tool only to 
persons who are familiar with this model 
and its operation and only with the 
instruction manual.

To operate the power tool you must be 
rested, in good physical condition and 
mental health.

If you have any condition that might be 
aggravated by strenuous work, check 
with your doctor before operating a 
power tool.

Persons with pacemakers only: The 
ignition system of your unit produces an 
electromagnetic field of a very low 
intensity. This field may interfere with 
some pacemakers. To reduce health 
risks, STIHL recommends that persons 
with pacemakers consult their physician 
and the pacemaker manufacturer before 
operating this tool.

Do not operate the power tool if you are 
under the influence of any substance 
(drugs, alcohol) which might impair 
vision, dexterity or judgment.

Use your power tool only for harvesting 
fruit about the size of coffee berries, 
nuts, olives, sloes, etc.

It must not be used for any other 
purpose since it may result in accidents 
or damage to the machine. Never 
attempt to modify

 

your power tool in any 

way since this may result in accidents or 
damage to the machine.

Safety Precautions and 

Working Techniques

Содержание SP 81







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды