manualshive.com logo in svg

Stihl SP 81, Инструкция по эксплуатации

Поделиться
Скачать
Stihl SP 81 Скачать руководство пользователя страница 17

16

English

SP 81

Mix Ratio

STIHL 50:1 two-stroke engine oil:
50 parts gasoline to 1 part oil

Other high-quality two-stroke engine 
oils:
25 parts gasoline to 1 part oil

Examples

:

Use a canister approved for storing 
fuel. Pour oil into the canister first, 
then add gasoline and mix 
thoroughly. 

Storing Fuel

Store fuel only in approved safety-type 
fuel canisters in a dry, cool and safe 
location protected from light and the sun.

Fuel mix ages:

 

Only mix sufficient fuel for a few weeks 
work. Do not store fuel mix for longer 
than 3 months.
Exposure to light, the sun, low or high 
temperatures can quickly make the fuel 
mix unusable.

:

Thoroughly shake the mixture in the 
canister before fueling your 
machine.

Pressure may build up in the 
canister – open it carefully.

:

Clean the fuel tank and canister 
from time to time.
Dispose of remaining fuel and 
cleaning fluid properly in 
accordance with local regulations 
and environment requirements.

:

Before fueling, clean the filler cap 
and the area around it to ensure that 
no dirt falls into the tank.

:

Always thoroughly shake the 
mixture in the canister before 
fueling your machine.

Take care not to spill fuel while fueling 
and do not overfill the tank. STIHL 
recommends use of the STIHL filling 
system (special accessory).

After fueling,

 

tighten fuel cap as 

securely as possible by hand. 

Gaso-
line

STIHL 
engine oil
50:1 

Other high-
quality two-
stroke engine 
oils:
25:1

Liters Liters

(cc) Liters

(cc)

1

0.02

(20) 0.04

(40)

5

0.10

(100) 0.20

(200)

10

0.20

(200) 0.40

(400)

15

0.30

(300) 0.60

(600)

20

0.40

(400) 0.80

(800)

25

0.50

(500) 1.00 (1000)

Fueling

389BA031 KN

Содержание SP 81







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды