manualshive.com logo in svg

Stihl SP 81, Инструкция по эксплуатации

Поделиться
Скачать
Stihl SP 81 Скачать руководство пользователя страница 22

21

SP 81

English

Dirty air filters reduce engine power 
increase fuel consumption and make 
starting more difficult.

If there is a noticeable loss of engine 
power

:

Move choke lever to 

g

.

:

Press in the tab

 

(

1

).

:

Ease the filter cover (

2

) over the tab 

and take it away.

:

Clean away loose dirt from around 
the filter.

:

Remove the foam and felt filter 
elements.

:

Wash the foam element in a clean, 
non-flammable cleaning solution 
(e.g. warm soapy water) and then 
dry.

:

Fit new felt element. 
As a temporary measure you can 
knock it out on the palm of your 
hand or blow it out with compressed 
air. 

Do not

 wash.

Replace damaged parts!

:

Install the foam element (

3

)

 

in the 

filter cover (

2

).

:

Place felt element (

4

)

 

(lettering 

facing inward) in filter housing (

5

).

:

Fit filter cover so that it snaps into 
position.

The carburetor comes from the factory 
with a standard setting.

This setting provides an optimum fuel-air 
mixture under most operating 
conditions.

With this carburetor it is only possible to 
adjust the high speed screw within fine 
limits.

Cleaning the Air Filter

355BA014 KN

2

1

2

3

355BA031 KN

4

5

355BA032 KN

Adjusting the Carburetor

265BA024 KN

LA

H

L
1

3 / 4

Содержание SP 81







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды