manualshive.com logo in svg

Stihl SP 81, Инструкция по эксплуатации

Поделиться
Скачать
Stihl SP 81 Скачать руководство пользователя страница 21

20

English

SP 81

If the engine still does not start

:

Move slide control to 

STOP-O

:

Remove the spark plug boot

 

(

10

).

:

Unscrew and dry off the spark plug.

:

Open the throttle wide.

:

Crank the engine several times with 
the starter to clear the combustion 
chamber.

:

Refit the spark plug. Connect the 
spark plug boot (press it down 
firmly).

:

Move slide control to 

START

.

:

Set the choke lever to 

e

, even if the 

engine is cold.

:

Now start the engine.

Adjustment of throttle cable

:

Check adjustment of the throttle 
cable – see “Adjusting the Throttle 
Cable”.

Fuel tank run until dry

:

After refueling, press the fuel pump 
bulb at least five times – even if bulb 
is filled with fuel.

:

Set the choke lever according to 
engine temperature.

:

Now start the engine.

During break-in period

A factory new machine should not be run 
at high revs (full throttle off load) for the 
first three tank fillings. This avoids 
unnecessary high loads during the 
break-in period.
As all moving parts have to bed in during 
the break-in period, the frictional 
resistances in the engine are greater 
during this period.
The engine develops its maximum 
power after about 5 to 15 tank fillings.

During operation

After a long period of full-throttle 
operation, allow engine to run for a while 
at idle speed so that the heat in the 
engine can be dissipated by flow of 
cooling air. This protects engine-
mounted components (ignition, 
carburetor) from thermal overload.

After finishing work

Storing for short period:
Wait for engine to cool down. Drain the 
fuel tank and keep the unit in a dry place, 
away from sources of ignition, until you 
need it again.
Storing for a long period:
see chapter "Storing the Machine".

393BA019 KN

10

Operating Instructions

Содержание SP 81







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды