STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 42

Страница: 42 / 72

| WPC | WPC cool www.stiebel-eltron.com

installation

shutting down

15. Shutting down

If the system is to be taken out of use, set the heat pump manager

to standby. This retains the safety functions designed to protect

the system (e.g. frost protection).
There is no need to shut the system down in summer. The heat

pump manager has an automatic summer / winter changeover.

Material losses

Never interrupt the power supply, even outside the heat-

ing period. The system's active frost protection is not

guaranteed if the power supply is interrupted.

Material losses

Observe the temperature application limits and the min-

imum circulation volume on the heat consumer side (see

chapter "Specification / Data table").

Material losses

If the heat pump and frost protection are completely

switched off, drain the system on the water side.

16. troubleshooting

WARNING Electrocution

Isolate the appliance from the power supply when

carrying out any work.

16.1 fault display

Faults/errors in the system or in the heat pump are indicated on

the display. For heating system and heat pump troubleshooting

and analysis, all important process data and bus subscribers can

be called up under DIAGNOSIS and a relay test can be carried out.

For troubleshooting, analyse all available parameters before

opening the heat pump control panel.

The heat pump manager will not indicate whether the electric

emergency/booster heater high limit safety cut-out has respond-

ed. The high limit safety cut-out can be reset by your contractor

through pressing the reset button. The high limit safety cut-out

response is generally caused by air in the heating circuit or an

inadequate heating flow rate.

Check the heating flow rate and ventilate the heating system.

16.2 fault message

If the appliance registers a fault, this is clearly displayed with the

message shown below.

cOMFORT MODE

FAUlT

SENSOR BREAK E 71

TUESDAY 25.JUN 13

16:27 TIME

If more than one fault occurs, the most recent fault is always

shown. Notify your qualified contractor.

16.2.1 Heat pump-specific or hardware faults

See chapter "Fault table".

16.2.2 the heat pump is not running

The heat pump is in standby mode [ ].

Change the system over to programmed operation.

The power supply has been blocked, POWER-OFF is displayed.

Wait for the blocking time to elapse. The heat pump will au-

tomatically start up again.

There is no heat demand.

Check the set and actual values under the INFO menu item.

There may be an incorrect fuse rating.

See chapter "Specification / Data table".

Note

The heat pump can only be restarted after the fault has

been removed and the heat pump has been reset (heat

pump reset parameter).

Additional parameters available for system analysis:

- QUICK START: The quick start must only be carried out by our

customer support. The heat pump compressor is checked

during a quick start.

- RELAY TEST: Test for all relays in the heat pump manager.

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды