STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 26

Страница: 26 / 72

| WPC | WPC cool www.stiebel-eltron.com

installation

00000

Remove the DHW temperature sensor from the immersion

pipe of the DHW cylinder.

Mark the immersion pipe.

Place the DHW temperature sensor safely in the refrigerant

circuit.

00000

500

Undo the hydraulic connection lines.

00000

1 Fixing screw

2 Handle

Remove the four fixing screws.

Lift the refrigeration unit off the DHW cylinder. To do this, use

the four handles in the base plate.

Position the DHW cylinder on the prepared base (see chapter

"Installation / Siting").

Reassemble the appliance in reverse order. Be sure to place

the DHW temperature sensor back in the marked sensor well.

11.2 Siting

Remove the packaging film and the top and side EPS

padding.

�0

3�

�1

1 Appliance foot

2 Sliding block

Undo the four fixing screws underneath the non-returnable

pallet.

Remove the appliance feet from the pack. Fully screw the feet

onto the appliance, without removing the appliance from the

pallet.

Take the appliance off the pallet and set it down on the pre-

pared base. If required, use the sliding blocks provided to

help you position the appliance.

For lifting, use the handles provided on the back panel and

the front adjustable rubber feet at the bottom.

Observe minimum distances (see chapter "Preparations /

Minimum clearances").

Level the appliance horizontally by adjusting the feet.

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды