STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 20

Страница: 20 / 72

oPeration

menu structure

| WPC | WPC cool www.stiebel-eltron.com

electric reHeatinG

dual mode temp dHW

Dual mode temperature of the heat pump for DHW heating.
Below this outside temperature, the electric emergency/booster

heater is switched on for DHW heating, subject to load.

loWer app limit dHW

Lower application limit of the heat pump for DHW heating.
The heat pump is switched off at outside temperatures below the

selected lower DHW application limit.
The electric emergency/booster heater alone provides DHW heat-

ing.

5.4.4 coolinG

The appliance is designed for DHW and central heating. Passive

cooling is possible in conjunction with the WPC cool. In the de-

livered condition, the COOLING parameter is set to OFF. Active

cooling mode is only possible in conjunction with the WPAC 2

cooling module.

coolinG

On / OFF

coolinG mode

PASSIVE COOLING / ACTIVE COOLING

active coolinG

area coolinG

FLOW TEMPERATURE

FLOW TEMP HYSTERESIS

SET ROOM TEMPERATURE

DYNAMIC

fan coolinG

FLOW TEMPERATURE

FLOW TEMP HYSTERESIS

SET ROOM TEMPERATURE

DYNAMIC

paSSive coolinG

area coolinG

FLOW TEMPERATURE

FLOW TEMP HYSTERESIS

SET ROOM TEMPERATURE

fan coolinG

FLOW TEMPERATURE

FLOW TEMP HYSTERESIS

SET ROOM TEMPERATURE

Appliance and system damage

You must not enable the COOLING parameter without a

cooling module.

Wpc 04 - 16 with Wpac 2 cooling module

Appliance and system damage

Set the COOLING parameter to ACTIVE COOLING.

Note

The COOLING parameter will only be shown if an FEK or

FE7 remote control is connected. Cooling mode is only

possible in summer mode.

the Wpc with the Wpac 2 cools in 2 stages:

Stage 1 (source pump)

Heat is extracted from the heating circuit and is passed to the

heat source system.

Stage 2 (source pump + compressor)

In addition, the refrigerant circuit extracts heat from the heating

circuit and transfers it to the heat source system.

dHW heating

DHW heating always has priority. As long as the actual tempera-

ture has not dropped below the set flow or room temperature, ac-

tive cooling continues even during DHW heating, and any extracted

heat is transferred to the DHW. If there is no cooling demand, DHW

is conventionally heated via the heat source system.

cooling mode with the fe7

The FE7 remote control is not equipped with dew point monitor-

ing. It can therefore only be used in conjunction with fan convec-

tors with condensate drain. The cooling mode parameter must

be set to FAN.

cooling mode with the feK

The FEK remote control is equipped with dew point monitoring,

and can therefore be used with area heating systems (e.g. under-

floor/wall heating systems, etc.). The COOLING parameter must be

set to AREA COOLING. The set flow temperature is compared with

the captured dew point temperature, so the actual temperature

never drops below the dew point. When using fan convectors

with the FEK remote control, set the COOLING parameter to FAN

COOLING.
In the COOLING parameter, you can select the following cooling

modes for the FE7 and the FEK:

- Room temperature

Cooling mode starts when the selected room temperature is

exceeded (output COOLING=230 V).

Cooling mode is stopped when the actual room temperature

drops 2 K below the set temperature. (output COOLING=0 V)

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды