STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 23

Страница: 23 / 72

www.stiebel-eltron.com

WPC | WPC cool |

installation

safety

installation

8. Safety

Only a qualified contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

8.1 General safety instructions

We guarantee trouble-free function and operational reliability only

if original accessories and spare parts intended for the appliance

are used.

8.2 instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

9. appliance description

9.1 mode of operation

The heat exchanger on the heat source side (evaporator) extracts

natural heat from the heat source. This extracted energy and the

energy drawn by the compressor drive is transferred to the heating

water by a heat exchanger on the heating water side (condenser).

Subject to the heat load, the heating water is heated up to +60 °C.

The DHW is heated via the internal indirect coil inside the DHW

cylinder.
The electric emergency/booster heater starts if the high pressure

sensor or the hot gas limiter responds during DHW heating. In

addition it covers any residual heat demand, if the heating system

demand exceeds the heat pump output.

9.2 Special features of the Wpc...cool

For cooling, the brine is pumped through a 3-way diverter valve

and a second heat exchanger, where the energy is extracted from

the heating water.

9.3 Standard delivery

The following are delivered with the appliance:

- 1 outside temperature sensor AFS 2

- 1 immersion sensor TF 6

- 2 elbow push-fit connectors 22 mm

- 2 elbow push-fit connectors 28 mm

- 2 pressure hoses DN 19 x 500 mm

- 2 pressure hoses DN 25 x 500 mm

9.4 accessories

- Brine charging unit WPSF

- Water softener fitting HZEA

- Filter assembly 22 mm (FS-WP 22)

- Filter assembly 28 mm (FS-WP 28)

- FE7 remote control

- FEK remote control

10. preparations

Note

The appliance is designed for internal installation, except

in wet areas.

Never install the appliance directly below or next to

bedrooms.

Protect pipe transitions through walls and ceilings with an-

ti-vibration insulation.

The room in which the appliance is to be installed must meet the

following conditions:

- No risk from frost.

- The room must not be subject to a risk of explosions arising

from dust, gases or vapours.

- When installing the appliance in a boiler room together with

other heating equipment, ensure that the operation of other

heating equipment will not be impaired.

- The volume of the installation room should be at least

13.8 m³.

- Load-bearing floor (for the weight of the unit, see chapter

"Specification / Data table").

For installation on floating screeds, make provisions for a

quiet heat pump operation.

Isolate the installation surface.

1 2 3

�0

3�

�1

1 Concrete base

2 Impact sound insulation

3 Floating screed

4 Recess

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды