STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 30

Страница: 30 / 72

| WPC | WPC cool www.stiebel-eltron.com

installation

Material losses

Carry out all water connection and installation work in

accordance with regulations.

Material losses

The "DHW outlet" connection is pre-fitted with a plastic

union nut and a soft rubber gasket.

The torque of the plastic union nut depends on the gasket

used.

15 Nm = pre-fitted soft rubber gasket.

25 Nm = alternative hard gasket.

Keep to the permissible torque.

Material losses

Operate the appliance only with pressure-tested taps.

11.9.1 permissible materials

cold water line

Galvanised steel, stainless steel, copper and plastic are approved

materials.

dHW line

Stainless steel, copper and plastic pipework are approved ma-

terials.

Material losses

The maximum permissible pressure must not be exceed-

ed (see chapter "Specification / Data table").

Install a type-tested safety valve in the cold water supply

line. For this bear in mind that, depending on the static pres-

sure, you may also need a pressure reducing valve.

The safety valve discharge aperture must remain open to the

atmosphere.

Install the safety valve discharge pipe with a constant fall to

the discharge outlet.

Size the discharge outlet so that water can drain off unim-

peded when the safety valve is fully opened.

Flush the pipes thoroughly.

�0

3�

�1

1 Drain (DHW cylinder)

Fill the DHW cylinder via the drain.

Open all downstream draw-off valves until the appliance is

full and the pipework is free of air.

Carry out a tightness check.

11.10 dHW circulation connection

The DHW circulation connector is located at the back of the appli-

ance (see chapter “Specification / Dimensions and connections”)

00000

1 Cap

Detach the panel.

Remove the foam parts.

Unscrew the cap.

Re-insert the foam parts.

Connect the DHW circulation line.

11.11 operation with buffer cylinder

Install the TF6 return sensor supplied.

Connect the return sensor to the control panel.

At the heat pump manager, set parameter BUFFER MODE to

ON.

11.12 fitting the push-fit connectors

Material losses

Tighten the screw cap of the push-fit connector by hand.

Never use a tool.

The push-fit connectors are equipped with a retainer with stain-

less steel serrations and an O-ring for sealing. In addition, they

are equipped with the "twist and lock" function. Simply turning

the screw cap by hand will secure the pipe in the connector and

push the O-ring against the pipe to seal it.

Material losses

Support sleeves are required when using plastic pipes.

Making the connection

The connector must be in its relaxed position before the pipe is

inserted. In this position, there is a small gap between the screw

cap and connector body.

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды