STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 32

Страница: 32 / 72

| WPC | WPC cool www.stiebel-eltron.com

installation

Power supply

12.2.1 compressor and electric emergency/booster heater

Appliance damage

The compressor must only rotate in one direction. If the

fault NO POWER appears in the WPM3i display when the

compressor starts, change the direction of rotation by

interchanging two phases.

appliance
function

effect of the electric emergency/booster heater

Mono energet-

ic operation

If the heat pump cannot reach the dual mode point, the elec-

tric emergency/booster heater ensures both the heating oper-

ation and the provision of high DHW temperatures.

Emergency

mode

Should the heat pump suffer a fault that prevents its contin-

ued operation, the heating output will be covered by the elec-

tric emergency/booster heater.

Connect cables according to the following diagram.

00000

X3 electric emergency/booster heater (DHC)

L1, L2, L3, N, PE

Connected load

terminal allocation

2.9 kW

5.8 kW

8.8 kW

X3 Compressor (HP)

L1, L2, L3, N, PE

12.2.2 control voltage

00000

X4 Control voltage (control outputs)

KUE

MKP

M(A)

M(Z)

HKP

Compressor signal

Brine pump signal

Cooling

Mixer circuit pump and N (X25), PE

Mixer open

Mixer closed

Heating circuit pump and N, PE

Pump

DHW

X4 Control voltage (control inputs)

L, L, N, PE Power supply
EVU

Enable signal

Material losses

Do not connect a high ef f iciency circula-

tion pump directly to control output UP.

Use an external relay with a breaking capacity of at least

10 A/250 V AC or our relay set WPM-RBS.

If no voltage is applied to the power supply utility enable signal,

the heat pump will not start. The message “power-OFF” appears

on the controller. In this event, install a jumper across “EVU” and

phase “L”.

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды