STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 24

Страница: 24 / 72

| WPC | WPC cool www.stiebel-eltron.com

installation

10.4.1 minimum clearances

≥500

≥200

≥1000

≥50

≥500

00000

Maintain the minimum clearances to ensure trouble-free op-

eration of the appliance and facilitate maintenance work.

10.1 electrical installation

DANGER Electrocution

Carry out all electrical connection and installation work

in accordance with national and regional regulations.

DANGER Electrocution

Use a permanent connection to the power supply. Ensure

the appliance can be separated from the power supply by

an isolator that disconnects all poles with at least 3 mm

contact separation. This requirement can be met with

contactors, circuit breakers, fuses, etc.

WARNING Electrocution

The appliance contains inverters (e.g. variable speed

compressors, high efficiency circulation pumps or high

efficiency fans). In case of a fault inverters can cause DC

residual currents. If RCDs are provided, they have to be

type B AC/DC-sensitive.

A DC residual current can block type A RCDs.

Make sure that the appliance power supply is dis-

connected from the fuse board/distribution panel.

Note

The specified voltage must match the mains voltage. Ob-

serve the type plate.

Install cables with the following cross-sections in accordance with

the respective fuse rating:

Fuse/mCB
rating

assignment

Cable cross-section

C 16 A

Compressor

2.5 mm²

B 16 A

Electric emergency/

booster heater (BH)

2.5 mm²

1.5 mm² with only two live cores and

routing on a wall or in an electrical con-

duit on a wall.

B 16 A

Control unit

1.5 mm²

The electrical data is provided in the chapter "Specification / Data

table".

Material losses

Provide separate fuses/MCBs for the two power circuits

of the compressor and the electric emergency/booster

heater.

11. installation

11.1 transport

Transport the appliance in its packaging to protect it against

damage.

Protect the appliance against heavy impact during transport.

- If the appliance needs to be tilted during transport only do so

for a short time to one of its longitudinal sides.

The longer the appliance is tilted, the greater the distribution

of refrigerant oil in the system.

- Storage and transport at temperatures below - 20 °C and

above + 50 °C are not permissible.

To facilitate transportation you can also divide the appliance by

removing the refrigeration unit.

11.1.1 dividing the appliance

Proceed as follows:

Remove the upper packaging.

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды