STIEBEL ELTRON WPC 04 Скачать руководство пользователя страница 41

Страница: 41 / 72

www.stiebel-eltron.com

WPC | WPC cool |

installation

settings

14. Settings

14.1 Standard settings

At the factory, the heat pump manager is programmed with the

following standard settings:

Switching times for heating circuit 1 and 2 (day mode)

only the 1st switching pair is pre-programmed.

Standard

Setting range

Monday - Friday

6:00 - 22:00

0:00 - 23:59

Saturday - Sunday

7:00 - 23:00

0:00 - 23:59

room temperature 1 / 2
standard settings without night setback.

Room temperature in day mode

20 °C

5 - 30 °C

Room temperature in night mode

20 °C

5 - 30 °C

DHW program switching times

Monday - Sunday

0:00 - 24:00

0:00 - 23:59

DHW temperature

DHW day temperature

50 °C

OFF / 50 - 70 °C

DHW night temperature

50 °C

OFF / 50 - 70 °C

Heating curve slope

Heating curve 1

0.6

0 - 5

Heating curve 2

0.2

0 - 5

14.2 Heating and dHW programs

You may enter your individual programs into the following tables.

14.2.1 Heating program, heating circuit 1

switching time
pair i

switching time
pair ii

switching time
pair iii

Mon

Tue

Wed

Thu

Fri

Sat

Sun

Mon - Fri

Sat - Sun

Mon - Sun

14.2.2 Heating program, heating circuit 2

switching time
pair i

switching time
pair ii

switching time
pair iii

Mon

Tue

Wed

Thu

Fri

Sat

Sun

Mon - Fri

Sat - Sun

Mon - Sun

14.2.3 dHW program

switching time
pair i

switching time
pair ii

switching time
pair iii

Mon

Tue

Wed

Thu

Fri

Sat

Sun

Mon - Fri

Sat - Sun

Mon - Sun

14.3 appliance handover

Explain the function of the appliance to users and familiarise them

with its operation.

Note

Hand over these operating and installation instructions

to the user for safe-keeping. Always carefully observe all

information in these instructions. They provide informa-

tion on safety, operation, installation and maintenance

of the appliance.

Содержание WPC 04









































































Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPC 04, Эксплуатация и установка

Результаты поиска

Содержание WPC 04

Отзывы:

Похожие инструкции для WPC 04

Бренды по названию

Популярные бренды