manualshive.com logo in svg

Stemin IS 6, Руководство пользователя, Страница: 19 / 29

Поделиться
Скачать
Stemin IS 6 Скачать руководство пользователя страница 19

STEMIN GmbH

Audio - Video - Control Engineering
82 549 Koenigsdorf - GERMANY

Vorab IS6_BDA_V1_01_eng.doc

Copyright 

©

 STEMIN GmbH 2007

Seite 19 von 29

5. Cleaning

Switch power to the central unit off and disconnect the power supply from mains before
cleaning. Use a cloth slightly moistened (not wet!) with water to clean the surfaces of
the central unit, power supply and conference terminals.
Never use caustic or scouring cleaners or cleaning agents containing alcohol or sol-
vents since these may damage the enamel or plastic parts.

6. Trouble shooting

Problem

Possible cause

Remedy

LED „ERROR“ lights up

1. Internal fuse defect

2. To much conference terminals 

at one line

3. Cable or conference terminal
    defect

1. Before opening the case, be sure, 

that the central unit is turned off and 
disconnected from mains.

    Replace the fuse with one of the 

same type.
If after the next activation the fuse is 
defect again, contact your dealer.

2. Decrease the number of conference 

terminals.

3. Disconnect one line after another. If 

you found the defective line, test 
which cable or conference terminal 
caused the problem and replace it.

No LED shines

1. Power supply interrupted

2. Central unit turned off

1. Connect the power supply to  the 

central unit as well as to the power 
outlet. If you connected the power 
supply to a switchable power circuit, 
switch the circuit on.

2. Set the POWER switch to  „ | “.

No sound at original signal

1. Central unit turned off

2. Input level to low

3. Controller INPUT ORIGINAL
    Volume is at left stop.
4. Cable defect

5. Volume control of conference 

terminals is at left stop.

6. Headphones connected

7. Mikrophone turned on.

1. Set the POWER switchs of all central
    units to „ | “.
2. Set the DIP-switch on the back of the 

central unit to +20dB  and / or increa-
se the level with the rotary control 
located at left of the XLR-socket.

  Check the level with the level indica-

tor.

3. Turn up the control

4. Exchange the cable, from which no 

more sound is to be heard.

5. Turn up the control

6. Disconnect the headphones or put 

them on.

7. Turn the microphone off.

Foreign languages can not be
monitored.

1. Controller LEVEL of the equal 

section „INTERPRETER-
BOOTH“ at left stop

2. Cable defect

1.  Turn up the respective control.

2.  Exchange the cable, from which no
       more sound is to be heard.

Содержание IS 6






























Отзывы:

Нет отзывов