background image

                                                                                                 SD1200 - Sectional Garage Door Opener 

Page 14 

 

                            Installation & Operating Instructions 

V2.09/19

 

 

 

Service Counter 

 

 

 

 

 

 

The opener has the following three (3) service intervals: 1,000 cycles, 1,500 cycles and 3,000 cycles. 
 
The opener will keep count of the number of operating cycles (an open and close of the door equals one 
cycle). Once the opener reaches the cycle count it will beep eight (8) times, every time you open your 
door. This audible alarm is a reminder that a professional service is recommended. To reset the cycle 
count to zero (0) follow the instructions below: 
 

 
Setting cycle count: 

 

Note: This procedure must be followed in sequence:  

 

1)

 

Press and hol

d the “P” and “-” buttons until there is a long beep, then release (there will be one (1) 

beep indicating the service counter has been set to 1,000 cycles) 

2)

 

Press and hold the “P” and “-” buttons until there is a long beep, then release (there will be two (2) 
beeps indicating the service counter has been set to 1,500 cycles) 

3)

 

Press and hold the “P” and “-” buttons until there is a long beep, then release (there will be three 
(3) beeps indicating the service counter has been set to 3,000 cycles) 

 
After eight (8) seconds the cycle count will be saved and you can operate your door as normal. To 
reset at any time, follow the sequence above to select the new cycle count. 

 

 
 
 
 

 
 
 
 
 
 

 

 

 

 

 

 

IMPORTANT-

 The garage door and opener must be professionally maintained and 

serviced regularly in accordance with the instructions provided with the product, as a 
minimum every 12 months or 1,500 cycles. 

 

This opener is pre-programmed with a service due reminder that will provide an 
audible indication that a service is recommended after 1,500 cycles. 

 

Is your opener beeping eight (8) times every time you open your door? 

 

This is an important reminder that a professional garage door service is 

recommended to keep your garage door and opener in optimal condition.

  

A poorly maintained door can cause property damage and result in serious or 

fatal injury.

 

Failure to properly maintain your garage door and opener may 

void your warranty. 

 

Please contact the company that installed your opener. You can usually find their 

contact details on a sticker affixed to the back of your garage door

.

 

Содержание SD1200



















Отзывы: