background image

                                                                                                 SD1200 - Sectional Garage Door Opener 

Page 2 

 

                            Installation & Operating Instructions 

V2.09/19

 

 

 

Important Safety Instructions

 

 
 

 

 

 

FAILURE TO COMPLY WITH THESE SAFETY RECOMMENDATIONS AND 
LOCAL  SAFETY  REGULATIONS  MAY  RESULT  IN  SERIOUS  INJURY, 
DEATH OR DAMAGE TO PROPERTY

 

PLEASE  READ  CAREFULLY  AND  ENSURE  THAT  ALL  SAFETY  RECOMMENDATIONS 
AND REGULATIONS ARE CONSIDERED AND ADHERED TO. 

 

 

 
 
 
 
 
 
 

 
 

 

This appliance is not intended for use by children or persons with reduced physical, sensory or mental 
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 
by a person responsible for their safety. 

 

Do not wear watches, rings or loose clothing while installing or servicing a garage door opener. Ensure 
that gloves, safety goggles and suitable protective clothing is worn where appropriate. 

 

The opener must not be installed in a wet or damp space exposed to weather. 

 

The opener must not be used on a door with a wicket door (a door within a door). 

 

Keep garage door balanced. Do not let the opener compensate for a binding or sticking garage door. 
Binding, sticking or unbalanced doors must be repaired before installing this opener. 

 

To avoid serious personal injury from entanglement, remove all ropes, chains and locks connected to the 
garage door before installing the door opener. 

 

Installation and wiring must be in accordance with your local building and electrical codes. 

 

Install the wireless remote control (transmitter) in a location where the garage door is visible, at a height 
of no less than 1.5m and out of reach of children. Do not allow children to operate push buttons or 
transmitters. Serious personal injury from a closing garage door may result from misuse of the opener. 

 

Permanently fasten the Warning Labels in prominent places, adjacent to wall controls and on manual 
release cord as a reminder of safe operating procedures. 

 

Ensure that the safety reverse system is tested every month. The garage door must reverse on contact 
with a 40mm high object placed on the floor. Adjust if necessary and repeat test. Failure to adjust 
properly may result in serious personal injury from a closing garage door. 

 

Disconnect electric power to the door opener before making repairs. 

 

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly 
qualified persons in order to avoid hazard. 

 

Frequently examine the door installation paying particular attention to the cables, springs and mountings 
for signs of wear, damage or imbalance. Springs and hardware are under extreme tension and a fault 
can cause serious personal injury. Do not use if repair or adjustment is needed. 

 

Ensure that the opener is operated only when door is in full view, free of obstructions and the opener is 
properly adjusted. No one should enter or leave the garage while the door is in motion. 

 

Do not allow children to play near the door, or with door controls. Keep remotes away from children. 

 

The door may operate unexpectedly, therefore do not allow anything to stay in the path of the door. 

 

SAVE THESE INSTRUCTIONS- it is important for the safety of persons to follow all instructions.

 

 
An emergency key release must be installed if there is no pedestrian door or other access into the garage. 
 
 
 

 

Note: It is highly recommended that safety beams are included with all installations. Correctly installed safety 
beams will prevent the door from closing if a person or object is located within the door area. If the beam is 
broken during the door’s downward travel it will reverse back to the open position.  

This accessory must be used for all installations where the closing force is greater than 400N (40kg 
of force) as measured at the bottom of the door.

 

Содержание SD1200



















Отзывы: