background image

22

745.089  | 11.30

EN

 

Exclusion of liability

The manufacturer can neither monitor the compliance with this manual nor the condi-

tions and methods during the installation, operation, usage and maintenance of the 

controller. Improper installation of the system may result in damage to property and, as 

a result, to bodily injury.

Therefore, the manufacturer assumes no responsibility and liability for loss, damage or 

costs which result from or are in any way related to incorrect installation, improper op-

eration, incorrect execution of installation work and incorrect usage and maintenance.

Similarly, we assume no responsibility for patent right or other right infringements of 

third parties caused by usage of this controller.

The manufacturer reserves the right to make changes to the product, technical data or 

installation and operating instructions without prior notice.

 

Legal guarantee

In accordance with German statutory regulations, there is a 2-year legal guarantee on 

this product for the customer. 

The seller will remove all manufacturing and material faults that occur in the product 

during the guarantee period and affect the correct functioning of the product. Natural 

wear and tear does not constitute a malfunction. No legal guarantee can be offered if 

the fault can be attributed to third parties, unprofessional installation or commissioning, 

incorrect or negligent handling, improper transport, excessive loading, use of improper 

equipment, faulty construction work, unsuitable construction location or improper op-

eration or use. Legal guarantee claims shall only be accepted if notification of the fault 

is provided immediately after it is discovered. Guarantee claims are to be directed to the 

seller. 

The seller must be informed before guarantee claims are processed. For processing 

a guarantee claim an exact fault description and the invoice / delivery note must 

be provided. 

The seller can choose to fulfil the legal guarantee either by repair or replacement. If the 

product can neither be repaired nor replaced, or if this does not occur within a suitable 

period in spite of the specification of an extension period in writing by the customer, the 

reduction in value caused by the fault shall be replaced, or, if this is not sufficient taking 

the interests of the end customer into consideration, the contract is cancelled.

Any further claims against the seller based on this legal guarantee obligation, in particu-

lar claims for damages due to lost profit, loss-of-use or indirect damages are excluded, 

unless liability is obligatory by law.

Содержание TF B001

























Отзывы: