Stanley SGM145, Оригинальное руководство пользователя

Страница: 7 / 44

7
ENGLISH (
Original Instructions)
tHe PacKaGe contaInS
1 Angle grinder
1 Guard
1 Side handle
1 Flange set
1 Two-pin spanner
1 Instruction manual
♦ Check for damage to the tool, parts or accessories
which may have occurred during transport.
♦ Take the time to thoroughly read and understand this
manual prior to operation.
Description (fig. a)
WARNING: Never modify the power tool or any
part of it. Damage or personal injury could result.
1 ON/OFF-switch
2 Lock button
3 Side handle
4 Guard
5 Spindle lock
eLectrIcaL Safety
Only one voltage is applicable to this tool. Be sure to check
that the power supply corresponds to the voltage on the
rating plate.
Your Stanley tool is equipped with double
insulation, hence, it does not require to be
earthed
When the power cord is damaged, have it sent to a
STANLEY service center for replacement to specially
prepared cables.
USInG an extenSIon caBLe
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool
(see technical Data ).The minimum conductor size is 1.5
mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
aSSeMBLy anD aDJUStMent
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect tool
from power source before making any
adjustments or removing/installing attachments or
accessories. Before reconnecting the tool, depress and
release the trigger switch to ensure that the tool is off. An
accidental start-up can cause injury.
attaching the Side Handle (fig. f)
WarnInG: Before using the tool, check that the
handle is tightened securely.
WarnInG: The side handle should always be
used to maintain control of the tool at all times.
Screw the side handle (3) tightly into one of the holes (15)
on thrin side of the gear case.
Mounting and removing the Guard
WarnInG: Guards must be used with this
grinder.
Mounting (fIG. B & c)
♦ Place the angle grinder on a table, spindle up.
♦ Align the lug (6) with the slot (7) in the bracket.
♦ Press the guard (4) down and turn it in the direction of
the arrow (Fig. B).
removing (fIG. B & c)
♦ Hold the tool in your hand.
♦ Loosen the screw 9 on the guard collar.
♦ Rotate the guard until the luglocates in the slot.
♦ Release the guard.
attaching and removing Grinding Wheels (fig. D, e)
Warning: Do not use damaged grinding wheels.
♦ Place the tool on a work bench, groove facing up.
♦ Attach the inner flange(11) correctly on the output
shaft(12) Fig. D
♦ Place the grinding wheel on the inner flange(11) when
attaching a grinding wheel with a raised center, make
sure that the raised center faces the inner flange.
♦ Place the sanding sheet on the rubber backing pad.
♦ Tighten the outer flange(14) until the output shaft (12)
(Fig.E) when attaching the grinding wheel, the ring on
top of the outer flange(14) must face the wheel.
♦ Press the spindle lock button (5) and prevent the
spindle (12) from rotating until it locks in place.
♦ Use the pin spanner to tighten the outer flange (14)
Prior to operation
♦ Install the appropriate guard and disk or wheel. Do not
use excessively worn disks or wheels.
♦ Do not use a damaged accessory. Before each use
inspect the accessory If power tool or accessory is
dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run the
power tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
♦ Be sure the inner and outer flange are mounted
correctly.
♦ Make sure the disk or wheel rotates in the direction of
the arrows on the accessory and the tool.
♦ Do not use cutting-off wheels for side grinding.
♦ Ensure that sparks resulting from use do not create
hazard e.g. do not hit persons, or ignite flammable
substances.