Stairmaster Crossrobics 1650 LE Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 108

background image

Page 51

PARTS REMOVAL AND REPLACEMENT

COVERS

Cover Fasteners

There are three types of covers: side covers, a seat tray, and weight stack
covers. All covers are held in place with reusable, plastic fasteners (see Figure
13 for their location). To remove the fasteners (see Figure 14):

1.

Slide either end of the fastener removal tool under the edge of the pin
head and pull the pin out about halfway. The pin should not be
removed. You may now pull the cover away from the frame. DO NOT
use the fastener removal tool or any other sharp tool to pry out the
fastener base because you may damage the covers.

2.

To reinstall the fastener, insert the base of the fastener through the
cover and into the frame. When the base is in place, push the pin in
all the way to secure the fastener.

Seat Tray

1.

Lift off the seat.

2.

Remove the two fasteners on top of the seat tray.

3.

Reinstall the seat tray with both fasteners and then set the seat into
the four mounting holes.

!

WARNING

DO NOT OPERATE THE MACHINE WHILE THE SIDE COVERS ARE REMOVED.

DO NOT DEPRESS OR RAISE THE PEDALS WHILE ANYONE’S HANDS ARE

INSIDE THE MACHINE. DO NOT WEAR LOOSE CLOTHING OR NECKTIES WHILE

WORKING ON THIS MACHINE WITH THE SIDE COVERS REMOVED.

GEARS, SPROCKETS, CHAINS AND BELTS OPERATE AT HIGH SPEEDS AND

HAVE THE POTENTIAL TO INFLICT SERIOUS BODILY INJURY.

«
...
58
59
60
61
62
...
»

Содержание Crossrobics 1650 LE













































































































Отзывы:

Нет отзывов

Похожие инструкции для Crossrobics 1650 LE

Бренд: ABB Страницы: 6

Movie FL Black E27 Flaps

Бренд: Qazqa Страницы: 2

Бренд: Jawbone Страницы: 3

Бренд: AAON Страницы: 36

Бренд: Rangevision Страницы: 28

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: Tar River Страницы: 61

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренд: Waves Страницы: 8

Бренд: BH FITNESS Страницы: 68

Бренд: Champlain Страницы: 4

DigitalMeltinchoc MCD101

Бренд: Martellato Страницы: 7

Бренд: ultraMEDIC Страницы: 28

Бренд: Evermed Страницы: 16

Бренд: Enerpac Страницы: 36

NOVACAT X8 COLL

Бренд: Pottinger Страницы: 91

Blue Bullet 1302-BAS

Бренд: BendPak Страницы: 68

Clinician Premiere Series

Бренд: OAKWORKS Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды