Stairmaster Crossrobics 1650 LE Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 108

background image

Page 57

PARTS REMOVAL AND REPLACEMENT

8.

Two sprockets are located on the right side of the shaft: a 30-tooth
drive sprocket and the smaller clutch sprocket. To remove the clutch
sprocket, slide it off the left side of the shaft.

9.

Remove the 30-tooth sprocket by removing the snap ring from the
right end of the shaft. Unscrew the allen head set screws located on
the inside flange of the drive sprocket.

10.

To reinstall the drive shaft, carefully reverse the disassembling
procedures. Install the drive shaft from the right side.

FLOATING PULLEY ASSEMBLY

1.

Remove the right and left side covers.

2.

Detach the weight stack belt at the frame junction.

3.

Remove the drive chain.

4.

Remove the floating pulley assembly (see Figure 26).

5.

Reverse the removal procedures to install. Make sure that the drive
chain and weight stack belt are routed properly.

6.

Reattach the side covers.

!

WARNING

TO REDUCE THE RISK OF EYE INJURY, WEAR EYE

PROTECTION WHEN REMOVING SNAP RINGS.

!

WARNING

TO REDUCE THE RISK OF EYE INJURY, WEAR EYE

PROTECTION WHEN REMOVING SNAP RINGS.

«
...
64
65
66
67
68
...
»

Содержание Crossrobics 1650 LE













































































































Отзывы:

Нет отзывов

Похожие инструкции для Crossrobics 1650 LE

Бренд: Taber Страницы: 27

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: HAMAR LASER Страницы: 49

Бренд: Facsimile Страницы: 16

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: Pari Страницы: 2

Бренд: Hammer Страницы: 42

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: tayco Страницы: 111

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренд: M-Audio Страницы: 3

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды