Stahl IS1, Руководство пользователя

Страница: 10 / 16

Digital Output Module Relay and Sockets for Installation in Zone 1 / Div. 1 Series 9477/12 / 9490
4
20 - - ·BA00·III·en·0 201526 / 9477610310 www.stahl-ex.com
2
perating Instructions for the IS1-System
IS1 I/O-Modules
Blinks Off In standby (switched on but no data
exchange with master yet)
• The module is in proper
condition but is not ready for
cyclic data exchange yet (there is no
parameter set available yet).
• The outputs are inactive.
Activate the cyclic data transfer with the
master.
Check the master, bus connection and
CPM.
Blinks Blinks Data Exchange has been quit (the
outputs are in safety
position)
Cyclic data transfer with master is inter-
rupted.
Activate the cyclic data transfer with the
master.
Check the master, bus connection and
CPM.
Blinks On Configuration fault Configuration is not correct or a
false module is connected.
Change configuration of master or con-
nect to the right module.
Off On or blinks I/O module hardware fault • Hardware check fault
• Eprom fault
• EEprom fault
Replace the I/O module.
Off Off Off No supply voltage at the I/O module or
defective I/O module.
• Check the power supply of the CPM.
• Check the CPM.
• Check the BusRail.
• Engage the I/O module correctly on
the BusRail.
• Replace the I/O module.
LED green
"RUN"
LED red
"ERR"
I/O Module status Source of fault Possible troubleshooting solution
Note
Contact the responsible sales subsidiary or our service department (support.instrumentati-
on@stahl.de) if the fault cannot be eliminated using available troubleshooting options.
Technical Data
Version 9477/12-08-12 (60 V) 9477/12-06-12 (250 V)
Certificates
IECEx
ATEX
IECEx PTB 06.0001X
PTB 01 ATEX 2205 X
IECEx PTB 06.0001X
PTB 01 ATEX 2205 X
Further certificates USA (FM), Canada (CSA),
Russia (CTB), Belarus (Gospromnadzor), Kazakhstan
(JSC), Brazil (INMETRO),
ship approval (DNV, ABS, GL, ClassNK)
USA (FM), Canada (CSA),
Russia (CTB), Belarus (Gospromnadzor), Kazakhstan
(JSC), Brazil (INMETRO),
ship approval (DNV, ABS, GL, ClassNK)
Explosion Protection
IECEx
ATEX
Ex d e [ia, ib] IIC T4
E II 2 G Ex d e [ia, ib] IIC T4
Ex d e [ia, ib] IIC T4
E II 2 G Ex d e [ia, ib] IIC T4
Output terminal Ex e II Ex e II
Further information see certificates see certificates
Galvanic isolation
between power supply and
system components
1500 V AC 1500 V AC
between two input / output
modules
500 V AC 500 V AC
between outputs and system
components
375 V AC 375 V AC
Outputs interconnected 60 V AC 250 V AC
Ex outputs
Maximum switching voltage
Maximum switching current
Maximum switching capacity
Number of channels 8 6
Contact NO NO
Minimum switching voltage 5 V AC / DC 5 V AC / DC
Minimum switching current 2 mA 2 mA
60 V AC 30 V DC 250 V AC 30 V DC 110V DC 220 V DC
2 A 2 A 2 A 2 A 0.3 A 0.12 A
100 VA 60 W 100 VA 60 W 33 W 26 W