SRAM Reverb Stealth2017 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 50

SRAM Reverb Stealth2017 Скачать руководство пользователя страница 9

9

Recommended Service Intervals

R e c o m m e n d e d S e r v i c e I n t e r v a l s

Regular service is required to keep your RockShox® product working at peak performance. Follow this maintenance schedule and install the service
parts included in each service kit that corresponds with the Service Hours Interval recommendation below. For spare part kit contents and details,
refer to the RockShox Spare Parts Catalog at

www.sram.com/service

.

Service Hours Interval

Maintenance

Every ride

Clean dirt and debris from seatpost.

Every ride

Check the remote hydraulic pressure.

Every ride

Inspect the upper post for scratches.

Every 50 Hours

Perform remote lever bleed

.

Every 50 Hours

Remove the lower post, clean, inspect and replace brass keys as needed, and apply new grease.

Every 200 Hours

Replace all parts included in the

Reverb™ Stealth B1 Service Kit - 200 hours.

Every 200 Hours

Perform full hydraulic remote system bleed

.

Every 400 Hours

Replace all parts included in the

Reverb Stealth B1 Service Kit - 400 hours.

S e r v i c e H i s t o r y

Record each date of service to track service intervals.

Service Hours Interval

50

100

150

200

250

300

350

400

Date of Service

B r a s s K e y S i z e

Size

= Record the number of etched lines on each key. Replace with the same

size keys

.

T o r q u e V a l u e s

Part

Tool

Torque

Poppet valve housing

11 mm open end wrench

5.7-7.9 N•m (50-70 in-lb)

Internal seal head

23 mm open end wrench

28 N•m (250 in-lb)

Poppet valve cover

10 mm open end wrench

5.7-7.9 N•m (50-70 in-lb)

Top cap assembly

34 mm open end wrench

27-29 N•m (238-256 in-lb)

Base plate lockring

26 mm open end wrench

9-10.2 N•m (79-90 in-lb)

Post hose barb sleeve

6 mm open end wrench

1.1-2.3 N•m (8-20 in-lb)

Post hose barb

7 mm open end wrench

3.4-4.5 N•m (30-40 in-lb)

Connectamajig™ coupler

9 mm open end wrench

3.4-4.5 N•m (30-40 in-lb)

Connectamajig hose coupler

6 mm open end wrench

1.1-2.9 N•m (10-26 in-lb)

Post bleed screw

T10 TORX® wrench

1.1-2.2 N•m (10-20 in-lb)

Remote bleed screw

T10 TORX wrench

1.1-2.2 N•m (10-20 in-lb)

Seatpost collar

Various

Do not exceed 6.7 N•m (59 in-lb)

Saddle clamp bolts

4 mm hex wrench

8-10 N•m (70-89 in-lb)

Remote lever hose barb

7 mm open end wrench

2.9-3.5 N•m (25-30 in-lb)

Remote lever clamp

T25 TORX wrench

2.8-3.4 N•m (25-30 in-lb)

«
...
7
8
9
10
11
...
»

Содержание Reverb Stealth2017



















































Отзывы:

Нет отзывов