SRAM Reverb Stealth2017 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 50

SRAM Reverb Stealth2017 Скачать руководство пользователя страница 26

26

Reverb Stealth B1 - Travel (mm)

Set the internal floating piston (IFP) height.
Use the chart below to determine the IFP depth for your Reverb
Stealth B1 seatpost. Use a marker to mark the Reverb IFP tool with the
IFP Depth (D) measurement.

Reverb Stealth B1 -

Travel (mm)

(D) IFP Depth (mm)

100

50

125

150

170

IFP height is critical to proper function. The graphics and

measurements on your Reverb IFP height tool may vary. Always

measure from the bottom of the tool and mark the tool with the

correct IFP depth for the Reverb Stealth B1 seatpost being serviced.

Set the internal floating piston (IFP) height. Use the Reverb™ IFP height
tool to push the IFP down

50 mm

into the upper post. Stop when the

measurement mark on the IFP tool is level with the top of the
upper post.
Remove the IFP height tool from the upper post.
Remove the upper post assembly from the vise and set it aside.

3

Reverb IFP height tool

170 mm

(D) 50 mm

Reverb Stealth B1 - All Travel Configurations

4

Reverb IFP height tool

50 mm

50 mm

«
...
24
25
26
27
28
...
»

Содержание Reverb Stealth2017



















































Отзывы:

Нет отзывов