SRAM Reverb Stealth2017 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 50

SRAM Reverb Stealth2017 Скачать руководство пользователя страница 27

27

Inner Shaft Assembly

4 0 0 H o u r S e r v i c e

I n n e r S h a f t A s s e m b l y

NOTICE

Do not scratch parts when you remove o-rings and seals. Do not
scratch any part with a sealing surface. Inspect each part for scratches.
Scratches can cause leaks and degrade product performance. Any part
with a scratch on a sealing surface must be replaced.
To remove external seals and o-rings, use your fingers to first pinch
the o-ring and lift it from the o-ring groove. Then use a pick to carefully
remove it.
To remove internal seals and o-rings, use a pick to pierce the seal or
o-ring and lift it from the o-ring groove. Then use a pick to carefully
remove it.
Use isopropyl alcohol and a clean rag to clean each part before
installing new seals.
Apply

only

SRAM

®

Butter grease to all new Reverb parts, seals

and o-rings.

Remove the inner shaft piston o-rings.
Apply SRAM Butter grease to new o-rings and install them onto, and
into, the inner shaft piston.

NOTICE

Do not scratch the inner shaft piston with the pick.

Apply a liberal amount of SRAM Butter grease to the inside of a

new

internal seal head assembly.
Install the internal seal head assembly onto the inner shaft, threaded
end first. Slide the internal seal head on the inner shaft until it stops
against the inner shaft piston.

Install a new bottom out o-ring and a new foam ring onto the
inner shaft.

1

Pick

Pick

2

3

«
...
25
26
27
28
29
...
»

Содержание Reverb Stealth2017



















































Отзывы:

Нет отзывов