SRAM Reverb Stealth2017 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 50

SRAM Reverb Stealth2017 Скачать руководство пользователя страница 38

38

Remote Lever

R e m o t e L e v e r

H o s e B a r b R e p l a c e m e n t ( o p t i o n a l )

If the hydraulic hose assembly is removed from the bicycle, refer to the Reverb™ Stealth User Manual at

www.sram.com/service

for installation

procedures. For a list of available Reverb Stealth hydraulic hose kits, refer to the RockShox® Spare Parts catalog at

www.sram.com/service

.

NOTICE

If Reverb hydraulic fluid leaks from the remote lever while under pressure or in use, the remote lever assembly must be replaced.

Use wire cutters to cut the cable tie used to secure the remote lever to
the bicycle handlebar.

Use needle nose pliers to hold the hydraulic hose near the hose barb.
Rotate the Reverb remote lever counterclockwise and unthread the
hose from the remote hose barb.

Optional

- If the remote hose barb is damaged from impact, it should

be replaced. Use a 7 mm open or box end wrench to remove the hose
barb from the remote lever.
Install a

new

hose barb into the lever and use a 7 mm open end

crowfoot socket and torque wrench, and tighten to
2.9-3.5 N•m (25-30 in-lb).

Thread the remote lever hose barb into the hydraulic hose. Use needle
nose pliers to hold the end of the hose at the hose barb and rotate the
remote lever clockwise while pushing the remote lever barb into the
hose. Stop when the hose is hand tight on the hose barb.

NOTICE

Do not over-tighten and strip the threads inside the hydraulic hose. If
the hose is over or under tightened, hydraulic fluid can leak.

The Reverb remote hydraulic system must be bled after the hose
is installed onto the remote lever. Proceed to the

Hydraulic Remote

System Bleed

section.

1

Wire cutters

2

Needle nose pliers

3

7 mm

4

Needle nose pliers

«
...
36
37
38
39
40
...
»

Содержание Reverb Stealth2017



















































Отзывы:

Нет отзывов