Spektrum NX6 Скачать руководство пользователя

Страница: 3 / 53

SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL

•  NX6 Transmitter (SPM6775, SPMR6775)
•  AR6610T Telemetry Receiver (SPM6775)
•  Manual

BEFORE USING YOUR TRANSMITTER

Before going any further, visit the Spektrum Community website at spektrumrc.com to register your transmitter and

download the latest Spektrum AirWare™ firmware updates. A registration reminder screen occasionally appears until

you register your transmitter. When you register your transmitter, the reminder screen does not appear again.

BOX CONTENTS

Support Videos:

For helpful videos on programming the NX6 and other Spektrum

AirWare™ equipped transmitters, go to www.spektrumrc.com/

IMPORTANT:

The NX6 includes channel 7 for limited functions.

This enables you have full functionality to fly BNF airplanes with

retracts, flaps and SAFE select with the NX6. Channel 7 is not a

fully proportional channel on the NX6, it cannot be used in mixes,

nor does it have travel adjustment. Channel 7 can be assigned

to a switch in the System Setup -> Channel Assign menu, it can

be reversed in the Function List -> Servo Setup menu, and it will

appear in the servo monitor.

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to state and local laws.

Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical

issues, excessive heat, FIRE, and ultimately injury and property damage.

• NEVER LEAVE THE BATTERY AND CHARGER UNATTENDED DURING USE
• NEVER CHARGE BATTERIES OVERNIGHT

• Read all safety precautions and literature prior to use of this product

• Never

allow minors to charge battery packs

• Never

drop charger or batteries

• Never

attempt to charge damaged batteries

• Never

attempt to charge a battery pack containing different types of batteries

• Never

charge a battery if the cable has been pinched or shorted

• Never

allow batteries or battery packs to come into contact with moisture at any time

• Never

charge batteries in extremely hot or cold places (recommended between 50–80˚ F or 10–27˚ C) or place in direct sunlight

• Always

disconnect the battery after charging, and let the charger cool between charges

• Always

inspect a new battery before charging

• Always

terminate all processes and contact Horizon Hobby if the product malfunctions

• Always

keep batteries and charger away from any material that could be affected by heat (such as ceramic and tile), as they can

get hot

• Always

end the charging process if the charger or battery becomes hot to the touch or starts to change form (swell) during the

charge process

BATTERY AND CHARGING PRECAUTIONS AND WARNINGS

SPECIFICATIONS

NX6 TRANSMITTER

Type

DSM2/DSMX 6 CH Telemetry Transmitter

Application

Airplanes, Helicopters, Sailplanes, Multirotors

Channels

7 (6 Full Channels, 7th SAFE Select Channel)

Wireless Trainer

DSM2*/DSMX Compatible

Switches

2 - 2 Position, 5 - 3 Position,

1 Momentary Button

Modulation

DSM2*/DSMX

Telemetry

Integrated

Bind Method

Bind Button or From Within Menu

Frame Rate

22ms Default,

11ms Selectable (Digital Servos Required)

Resolution

2048

Battery

3.7V 2,000 mAh LiIon

Band

2.4GHz

Feedback

Tone, Vibration, Voice

*EU versions of the NX6 are not compatible with DSM2

receivers.

Содержание NX6






















































Результаты поиска

Содержание NX6

Отзывы:

Похожие инструкции для NX6

Бренды по названию

Популярные бренды

Spektrum NX6, Инструкция по эксплуатации

Результаты поиска

Содержание NX6

Отзывы:

Похожие инструкции для NX6

Бренды по названию

Популярные бренды