Spektrum NX6 Скачать руководство пользователя

Страница: 32 / 53

SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL

FUNCTION LIST

Dual Rates and Exponential are available on the aileron, elevator

and rudder channels.

To adjust the Dual Rate and Exponential:

1. Scroll to the channel and press the scroll wheel once. Scroll

left or right to select the channel you wish to change and

press the scroll wheel again to save the selection.

2. Scroll to Switch and select the switch to activate D/R and

Expo for that channel.

3. Scroll to dual rate and press the scroll wheel. Scroll left or

right to change the value and press the scroll wheel again to

save the selection.

Exponential affects control response sensitivity around center but

has no affect on overall travel. Positive exponential decreases the

sensitivity around the center of gimbal movement.

The Differential screen enables you to increase or decrease the

amount of differential between aileron control surface throws.
Positive Differential values decrease the amount of “down” travel

without affecting the “up” travel on the opposite control surface.
Negative Differential values decrease the amount of “up” travel

without affecting the amount of “down” travel on the opposite

control surface.
The Differential menu option only appears when a multi-servo

aileron wing type is active in Aircraft Type.

To adjust the Differential:

1. Scroll to Switch and press the scroll wheel. Scroll right to

select On (Differential is always on) or assign the differential

to a switch position.

2. Press the scroll wheel a second time to save the selection.
3. Scroll to the percentage selection and press the scroll wheel

once to change the value.

4. Press the scroll wheel again to save the selection.

The Throttle Cut menu option enables you to assign a switch

position to stop an engine or motor. Throttle Cut activates

regardless of Flight Mode.

When you activate Throttle Cut, the throttle channel moves to the

pre-programmed position (normally Off).

You may need to use a negative value to move the Throttle channel

to the off position.

CAUTION:

Always test the model after making

adjustments to make sure the model responds to

controls as desired.

You can use the Throttle Curve menu option to optimize the throttle

response. A maximum of 7 points are available on the throttle

curve.

To add points to a Throttle Curve:

1. Move the throttle stick to the position where you wish to add

the new point.

2. Scroll to Add Pt. and press the scroll wheel to add the point.

To remove points from a Throttle Curve:

1. Move the Throttle stick until the cursor is near the point you

wish to remove.

2. Scroll to Remove Pt. and press the scroll wheel once to

remove the point.

If you program multiple throttle curves and you wish to edit one of

the curves, that curve must be active in the Throttle Curve screen

before you can make any changes.

Dual Rates and Expo

Differential (Acro and Sail Types Only)

Throttle Cut (Acro and Heli Types Only)

Throttle Curve (Acro and Heli Types Only)

Содержание NX6






















































Результаты поиска

Содержание NX6

Отзывы:

Похожие инструкции для NX6

Бренды по названию

Популярные бренды

Spektrum NX6, Инструкция по эксплуатации

Результаты поиска

Содержание NX6

Отзывы:

Похожие инструкции для NX6

Бренды по названию

Популярные бренды