Speeflo 449-500, Руководство пользователя

Страница: 23 / 32

© Titan Tool Inc. All rights reserved. 23
28
27a
27
Item Part # Description Quantity
1 235-018 Trip retainer.........................................2
2 141-007 O-ring ..................................................2
3 325-005 Trip spring, .........................................2
4 569-016 Ball, SS ...............................................2
5 441-908 Spool / sleeve set ...............................1
6 441-152 O-ring ..................................................3
7 235-030 Cylinder head plug..............................1
8 441-217 O-ring ..................................................1
9 858-811 Flex lock nut .......................................1
10 818-002 Street elbow, 90º.................................1
11 235-112 Cylinder head......................................1
12 431-032 O-ring ..................................................2
13 431-053 Sleeve retainer....................................1
14 431-054 Retainer ring .......................................1
15 192-000 Elbow ..................................................1
16 235-022 Piston retainer screw ..........................1
17 235-014 Piston ..................................................1
18 235-027 Piston seal ..........................................1
19 235-026 O-ring ..................................................1
20 235-021 Valve rod assembly.............................1
21 235-948 Piston rod............................................1
22 235-001 Lock ring .............................................1
23 235-007 Cylinder...............................................1
24 235-028 Rod seal..............................................1
25 235-929 Motor pump block ...............................1
26 235-029 Motor tube...........................................1
27 197-031 Tee ......................................................1
27a 431-019 O-ring kit .............................................1
28 700-499 O-ring ..................................................1
Reassembly of Hydraulic Motor
1. Separate spool/sleeve set (5). Place o-rings (6) onto sleeve.
Lubricate o-rings with hydraulic oil. Gently push the sleeve
into cylinder head (11) with the flatter side of the sleeve facing
out. Use a nylon rod to tap sleeve down until it reaches its full
depth. Do not use any other type of tool that might damage or
leave particles or residue on the sleeve. Install the spool
through the top of the cylinder head, down into the sleeve.
Do not use Piston Lube pump packing lubricant. It is a
solvent and will severely damage seals and O-Rings of the
hydraulic motor.
2. Install o-rings (2) on trip retainers (1). Install trip retainer balls
(4) followed by springs (3) which, when installed, will hold
spool/sleeve set (5) in proper place for assembly.
3. Install sleeve retainer (13) followed by snap ring (14) into
cylinder head (11), which will hold valve sleeve in place.
Install o-ring (12) in the o-ring groove of the cylinder head.
4. Replace lower seal (24) in motor block (25). Be sure the
open portion of the seal is facing upward (V). This seal
requires no special tool.
5. Place piston rod (21) in vise. Inspect valve rod assembly
(20) for any damage. Make sure the lock nut at the bottom
of the valve rod assembly (20) is secure. DO NOT remove.
Then, place into piston rod (21) as illustrated. Install o-ring
(19), lubricating it well and replacing piston (17) onto piston
rod (21). Put one drop of blue Loctite on the piston retainer
screw (16). Tighten piston retainer screw until piston is
locked into place. Check valve rod assembly (20) for normal
spring action at this time.
6. Install piston seal (18) with lips facing downward. Carefully
install piston seal (18). Expand the ring and stretch it
sufficiently for installation.
7. With motor pump block (25) still in vise, install lower seal
(24) by pushing it towards its groove with a properly sized
blunt rod. Then complete installation with the fingers. No tool
is necessary. Do not twist the seal.
CAUTION