manualshive.com logo in svg

Spectrex SafEye 200 Series, Руководство пользователя и по обслуживанию

Поделиться
Скачать
Spectrex SafEye 200 Series Скачать руководство пользователя страница 19

SafEye

™

™

Series 200 IR Gas Detector - User’s and Maintenance Manual

SPETCREX INC.

Doc. No. TM792100, Rev. B, Oct..1997

- 14 -

1. 10. System Setup

1. 10. 1.

Detector Setting

The detector consists of the following DIP Switches which enable the user to adapt
the detector operation to specific application:

SW1 - Function Selection Switch. Contains. 8 DIP Switches. Used for Calibration of

different gas selection, response time control and Relays response
configuration.

SW2 - Address Selection Switch. Contains 8 DIP Switches. Used for Detector’s

address setting and 4-20mA output configuration setting.

SW3 - Alarm Options Selection Switch. Contains 4 DIP Switches. Used for

Detector’s Alarm Latching configuration and 4-20 mA level reading
configuration.

Function Selection Switch:

Table 1-7 describes SW1 DIP Switches position and the required function for setting
the detector. according to the necessary configuration

Table 1-7. SW1 DIP Switches Configuration

Switch

No.

off  position

on  position

Default

setting

1.

Detection speed control bit 0 at “0”
(see note 1 below)

Detection speed control bit 0 at “1”
 (see note 1 below)

on

2.

Detection speed control bit 1 at “0”
(see note 1 below)

Detection speed control bit 1 at “1”
(see note 1 below)

off

3.

Gas type control bit 0 at “0
(see note 2 below)”

Gas type control bit 0 at “1”
(see note 2 below)

off

4.

Gas type control bit 1 at “0
(see note 2 below)”

Gas type control bit 1 at “1”
(see note 2 below)

off

5.

Full scale sensitivity is 0-5 LEL

x

m

Full scale sensitivity is 0-2 LEL

x

m

off

6.

Zero calibration is performed
according to background

Gas level detection performed without
background Zero calibration

off

7.

Accessory Relay is activated at
Warning level

Accessory Relay is activated at Alarm
level (with the Alarm Relay)

off

8.

Accessory Relay is activated
according to SW1-7 position

Accessory Relay is Activated at Power
on continuously ( used as End of Line)

off

Notes:
1.

Detection flashes rate can be selected by pre-setting of SW1-1 and SW1-2
according to the following table. There are two bits which provides four Flash
Source rates. Same Flash rate should be set also at the Flash Source.

Table 1-8. Flash Source Flash Rate Configuration

bit #0 position

(SW1-1)

bit #1 position

(SW1-2)

Source flash Rate

(flashes/second)

off

off

0.5

on

off

1

off

on

2

on

on

4

Содержание SafEye 200 Series



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды