manualshive.com logo in svg
background image

4

WARNING: 

Before Installing this product, read and follow all warning notices and instructions which are included. 

Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call 
1-800-223-8538 or visit www.usa.speck-pumps.com for additional copies of these instructions.

 

Important Safety Instructions

Swim Jet Combination Fitting - Manufacturers Warnings

MUST BE INSTALLED by an experienced and qualified pool industry professional ONLY.

Attention Installer: This manual contains important information about installation, operation, and safe use of 
this product. This information should be given to the owner and/or operator of this equipment. Most Federal, State 
and Local codes regulate the construction, installation and operation of pools and spas. It is important to comply 
with these codes, many of which regulate the installation and use of this product.

1. 

DO NOT locate this fitting in seating areas or on the back rests for such seating areas.

2.

 This fitting should be mounted in the vertical pool wall only per manufacturer’s instructions.

3. 

All fittings and fasteners should be examined for damage or tampering before each use.

 
4. 

Any missing, broken, or cracked fittings must be replaced before using this product. Only genuine Speck 

replacement parts may be used.

5. 

Acceptable fittings/pipe sizes are listed on page 7 of this manual. No other sizes are permitted.

 
6. 

Never exceed the maximum flow rate stated on this product.

7. 

The anti-entrapment cover must be in place when using this product. DO NOT use this product if the cover is 

missing, broke or loose.

8. 

The stainless steel anti-entrapment cover (part# 93.1) should be replaced within 20 years from installation 

date. The suction housing (part # 93) should be replaced within 10 years from installation date.

9. 

Installation requires a Phillips screw driver. All screws should be hand tight only. DO NOT use electrical or air 

drills.

10. 

Consult your physician before exercising with the BaduJet Imperial or using the massage hose.

11. 

DO NOT permit children to use this product unless they are closely supervised at all times.

12. 

DO NOT remove any safety alert labels such as

 

DANGER, WARNING,

 

or CAUTION

Keep safety alert labels in 

good condition and replace missing or damaged labels.

13. 

Stay alert, watch what you are doing and use common sense. DO NOT use unit if you are tired and/or 

exhausted.

 

DO NOT use unit while under the influence of drugs, alcohol, or any medications

14. CAUTION: 

DO NOT increase pump size; this will increase the flow rate through the system and exceed the 

maximum flow rate stated on this product.

  

IMPROPER INSTALLATION OR USE OF THIS PRODUCT MAY PRESENT A RISK OF HAIR OR BODY ENTRAPMENT 

AND DROWNING.

 

Install this equipment in accordance with the instructions provided.

Содержание badu jet imperial































Отзывы: