Sovan's CTD10R-E Скачать руководство пользователя страница 26

Страница: 26 / 45

The stacker can not
start.(The

contactor

works.)

①

The side-magnetic brake of the

drive wheel does not suck and
the stacker is in a braked
condition.

Repair or replace

②

The walking motor carbon brush is

worn or bad contact between the
steering

device

and

the

carbon-brush.

Repair or replace

③

The magnet-exciting coil of the

stepper motor is broken or bad
contact at the wire end.

Repair or replace

④

Bad contact.

Repair or replace

⑤

There is a trouble at the MOSFET

tube type circuit board.

Repair or replace

The stacker can only
move

forward

backward.

①

The contactor is in poor connection

or burnt out.

Repair or replace

②

There is malfunction in circuit

board.

Repair or replace

The stacker can not stop
during traveling.

Broken contact. The moving contact
cannot be reset.

Cut off the power at
once and replace the
contact

The brake does not work

①

The erection bolt of the fine motion

switch looses or is damaged.

Adjust or tighten the
bolt or replace the fine
motion switch.

②

The connecting wire of the

side-magnet brake is loose or
damaged

Tighten the bolt or
repair the side-magnet
brake.

③

The braking plates of the

side-magnet brake are worn.

Replace the braking
plates.

The steering has got
stuck

①

The bearing of the steering device

is damaged.

Replace the bearing

②

The bearing of the steering device

lacks lubricant or there is too
much dust

Clean the bearing

Difficult steering of the
drive wheel, noise and
the motor is overloaded.

①

The gear or bearing has got stuck

because of foreign matters.

Clean or replace the
bearing

②

There is a gap in the bearing

installed

Adjust the clearance

③

The front wheel bearing is

damaged.

Replace the bearing

The forks cannot be
lifted.

①

Overload

Reduce the load

②

The pressure of the overflow valve

is too low

Adjust the pressure
higher

③

Internal abnormal leakage in the Replace the seals

Содержание CTD10R-E














































Результаты поиска

Содержание CTD10R-E

Отзывы:

Похожие инструкции для CTD10R-E

Бренды по названию

Популярные бренды

Sovan's CTD10R-E, Руководство по эксплуатации

Результаты поиска

Содержание CTD10R-E

Отзывы:

Похожие инструкции для CTD10R-E

Бренды по названию

Популярные бренды