Southland OMD-525X Скачать руководство пользователя | Manualshive

Страница: 8 / 36

background image

1.5

Location Installation Considerations

The Southland Sensing OMD-525X Oxygen Analyzer is designed to be wall mounted in a general

purpose area and uses a NEMA4X / IP66 Enclosure. When installed outdoors in cold areas an optional

heater is recommended as well. Consider also giving the analyzer a sun shield if it is going to be

mounted in the direct sunlight.

Reference your local electrical authority for the proper installation.

The analyzer is EMI / RFI protected, however it is good practice not to mount it too close to sources

of electrical interference such as large transformers, motor start contactors, relays, large pumps, etc.

Also avoid subjecting the analyzer to significant vibration.

Mount the unit at a suitable eye level to easily read the local display. Gas connections are located on

the top right side of the analyzer, ensure there is adequate room to hook up your gas lines.

1.6

Safety Considerations

The oxygen analyzer is designed for installation into a general purpose area. Please follow your local

electrical code.

Designed, Tested, and Assembled in California, USA

4045 E. Guasti Rd. #203 Ontario, CA 91761 USA : 1-949-398-2879 : [email protected] : www.sso2.com

Introduction

OMD-525X Oxygen Analyzer

«
...
6
7
8
9
10
...
»

Содержание OMD-525X





































Отзывы:

Нет отзывов

Похожие инструкции для OMD-525X

Бренд: Olympus Страницы: 362

Бренд: Olympus Страницы: 8

Бренд: Velleman Страницы: 96

Бренд: Omega Страницы: 24

Бренд: GARANT Страницы: 368

Бренд: Bogen Страницы: 14

Бренд: Kurzweil Страницы: 12

Бренд: FM Marin Страницы: 8

Thermo Scientific iCE 3000 Series

Бренд: ThermoFisher Scientific Страницы: 42

Бренд: MULTISPAN Страницы: 4

Бренд: J&D Electronics Страницы: 2

Photo Research PR-810

Бренд: Jadak Страницы: 120

Бренд: Hanna Instruments Страницы: 2

Smart Photometer System iDip 570

Бренд: eXact Страницы: 16

Бренд: SRS Labs Страницы: 11

Бренд: Niigata seiki Страницы: 2

Бренд: Geokon Страницы: 19

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды